295 lines
9.8 KiB
C
295 lines
9.8 KiB
C
#include "freertos/FreeRTOS.h"
|
|
#include "freertos/task.h"
|
|
#include "driver/gpio.h"
|
|
#include "esp_log.h"
|
|
#include <ds18x20.h>
|
|
|
|
#include "inputs.h"
|
|
|
|
#define MAX_DN18B20_SENSORS 4U
|
|
#define ONE_WIRE_LOOPS 2U // try to read the 1-Wire sensors that often
|
|
#define PERIODIC_INTERVAL 1U // read and compute the inputs every 1sec
|
|
|
|
static const char *TAG = "smart-oil-heater-control-system-inputs";
|
|
const uint8_t uBurnerFaultPin = 19U;
|
|
const uint8_t uDS18B20Pin = 4U;
|
|
|
|
const onewire_addr_t uChamperTempSensorAddr = 0x3e0000001754be28;
|
|
const onewire_addr_t uOutdoorTempSensorAddr = 0x880000001648e328;
|
|
const onewire_addr_t uInletFlowTempSensorAddr = 0xe59cdef51e64ff28;
|
|
const onewire_addr_t uReturnFlowTempSensorAddr = 0xa7a8e1531f64ff28;
|
|
|
|
onewire_addr_t uOneWireAddresses[MAX_DN18B20_SENSORS];
|
|
float fDS18B20Temps[MAX_DN18B20_SENSORS];
|
|
size_t sSensorCount = 0U;
|
|
|
|
static SemaphoreHandle_t xMutexAccessInputs = NULL;
|
|
static eBurnerErrorState sBurnerErrorState;
|
|
static sMeasurement sChamperTemperature;
|
|
static sMeasurement sOutdoorTemperature;
|
|
static sMeasurement sInletFlowTemperature;
|
|
static sMeasurement sReturnFlowTemperature;
|
|
|
|
void taskInput(void *pvParameters);
|
|
void updateAverage(sMeasurement *pMeasurement);
|
|
|
|
void initInputs(void)
|
|
{
|
|
|
|
gpio_config_t ioConfBurnerFault = {
|
|
.pin_bit_mask = (1ULL << uBurnerFaultPin), // Pin mask
|
|
.mode = GPIO_MODE_INPUT, // Set as inout
|
|
.pull_up_en = GPIO_PULLUP_ENABLE, // Enable pull-up
|
|
.pull_down_en = GPIO_PULLDOWN_DISABLE, // Disable pull-down
|
|
.intr_type = GPIO_INTR_DISABLE // Disable interrupts
|
|
};
|
|
|
|
gpio_config(&ioConfBurnerFault);
|
|
|
|
xMutexAccessInputs = xSemaphoreCreateRecursiveMutex();
|
|
if (xMutexAccessInputs == NULL)
|
|
{
|
|
ESP_LOGE(TAG, "Unable to create mutex");
|
|
}
|
|
xSemaphoreGiveRecursive(xMutexAccessInputs);
|
|
|
|
BaseType_t taskCreated = xTaskCreate(
|
|
taskInput, // Function to implement the task
|
|
"taskInput", // Task name
|
|
4096, // Stack size (in words, not bytes)
|
|
NULL, // Parameters to the task function (none in this case)
|
|
5, // Task priority (higher number = higher priority)
|
|
NULL // Task handle (optional)
|
|
);
|
|
|
|
if (taskCreated == pdPASS)
|
|
{
|
|
ESP_LOGI(TAG, "Task created successfully!");
|
|
}
|
|
else
|
|
{
|
|
ESP_LOGE(TAG, "Failed to create task");
|
|
}
|
|
}
|
|
|
|
void updateAverage(sMeasurement *pMeasurement)
|
|
{ /* Average form the last 10sec */
|
|
pMeasurement->average10s.samples[pMeasurement->average10s.bufferIndex] = pMeasurement->fCurrentValue;
|
|
pMeasurement->average10s.bufferIndex = (pMeasurement->average10s.bufferIndex + 1) % AVG10_SAMPLE_SIZE;
|
|
|
|
if (pMeasurement->average10s.bufferCount < AVG10_SAMPLE_SIZE)
|
|
{
|
|
pMeasurement->average10s.bufferCount++;
|
|
}
|
|
|
|
if (pMeasurement->average10s.bufferCount == 0U)
|
|
{
|
|
pMeasurement->average10s.fValue = pMeasurement->fCurrentValue;
|
|
}
|
|
|
|
float sum = 0.0;
|
|
for (int i = 0; i < pMeasurement->average10s.bufferCount; i++)
|
|
{
|
|
sum += pMeasurement->average10s.samples[i];
|
|
}
|
|
|
|
pMeasurement->average10s.fValue = sum / pMeasurement->average10s.bufferCount;
|
|
|
|
/* Average form the last 60sec */
|
|
pMeasurement->average60s.samples[pMeasurement->average60s.bufferIndex] = pMeasurement->fCurrentValue;
|
|
pMeasurement->average60s.bufferIndex = (pMeasurement->average60s.bufferIndex + 1) % AVG60_SAMPLE_SIZE;
|
|
|
|
if (pMeasurement->average60s.bufferCount < AVG60_SAMPLE_SIZE)
|
|
{
|
|
pMeasurement->average60s.bufferCount++;
|
|
}
|
|
|
|
if (pMeasurement->average60s.bufferCount == 0U)
|
|
{
|
|
pMeasurement->average60s.fValue = pMeasurement->fCurrentValue;
|
|
}
|
|
|
|
sum = 0.0;
|
|
for (int i = 0; i < pMeasurement->average60s.bufferCount; i++)
|
|
{
|
|
sum += pMeasurement->average60s.samples[i];
|
|
}
|
|
|
|
pMeasurement->average60s.fValue = sum / pMeasurement->average60s.bufferCount;
|
|
}
|
|
|
|
void taskInput(void *pvParameters)
|
|
{
|
|
while (1)
|
|
{
|
|
vTaskDelay(PERIODIC_INTERVAL * 1000U / portTICK_PERIOD_MS);
|
|
if (xSemaphoreTakeRecursive(xMutexAccessInputs, portMAX_DELAY) == pdTRUE)
|
|
{
|
|
sChamperTemperature.state = MEASUREMENT_FAULT;
|
|
sOutdoorTemperature.state = MEASUREMENT_FAULT;
|
|
sInletFlowTemperature.state = MEASUREMENT_FAULT;
|
|
sReturnFlowTemperature.state = MEASUREMENT_FAULT;
|
|
|
|
if (gpio_get_level(uBurnerFaultPin) == 1)
|
|
{
|
|
sBurnerErrorState = FAULT;
|
|
}
|
|
else
|
|
{
|
|
sBurnerErrorState = NO_ERROR;
|
|
}
|
|
|
|
if (ds18x20_scan_devices(uDS18B20Pin, uOneWireAddresses, MAX_DN18B20_SENSORS, &sSensorCount) != ESP_OK)
|
|
{
|
|
ESP_LOGE(TAG, "1-Wire device scan error!");
|
|
}
|
|
|
|
if (!sSensorCount)
|
|
{
|
|
ESP_LOGW(TAG, "No 1-Wire devices detected!");
|
|
}
|
|
else
|
|
{
|
|
// ESP_LOGI(TAG, "%d 1-Wire devices detected", sSensorCount);
|
|
|
|
if (sSensorCount > MAX_DN18B20_SENSORS)
|
|
{
|
|
sSensorCount = MAX_DN18B20_SENSORS;
|
|
ESP_LOGW(TAG, "More 1-Wire devices found than expected!");
|
|
}
|
|
|
|
for (size_t iReadLoop = 0; iReadLoop < ONE_WIRE_LOOPS; iReadLoop++)
|
|
{
|
|
if (ds18x20_measure_and_read_multi(uDS18B20Pin, uOneWireAddresses, sSensorCount, fDS18B20Temps) != ESP_OK)
|
|
{
|
|
ESP_LOGE(TAG, "1-Wire devices read error");
|
|
}
|
|
else
|
|
{
|
|
for (int j = 0; j < sSensorCount; j++)
|
|
{
|
|
float temp_c = fDS18B20Temps[j];
|
|
// ESP_LOGI(TAG, "Sensor: %08" PRIx64 " reports %lf°C", (uint64_t)uOneWireAddresses[j], temp_c);
|
|
|
|
switch ((uint64_t)uOneWireAddresses[j])
|
|
{
|
|
case ((uint64_t)uChamperTempSensorAddr):
|
|
sChamperTemperature.fCurrentValue = temp_c;
|
|
sChamperTemperature.state = MEASUREMENT_NO_ERROR;
|
|
updateAverage(&sChamperTemperature);
|
|
break;
|
|
case ((uint64_t)uOutdoorTempSensorAddr):
|
|
sOutdoorTemperature.fCurrentValue = temp_c;
|
|
sOutdoorTemperature.state = MEASUREMENT_NO_ERROR;
|
|
updateAverage(&sOutdoorTemperature);
|
|
break;
|
|
case ((uint64_t)uInletFlowTempSensorAddr):
|
|
sInletFlowTemperature.fCurrentValue = temp_c;
|
|
sInletFlowTemperature.state = MEASUREMENT_NO_ERROR;
|
|
updateAverage(&sInletFlowTemperature);
|
|
break;
|
|
case ((uint64_t)uReturnFlowTempSensorAddr):
|
|
sReturnFlowTemperature.fCurrentValue = temp_c;
|
|
sReturnFlowTemperature.state = MEASUREMENT_NO_ERROR;
|
|
updateAverage(&sReturnFlowTemperature);
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
xSemaphoreGiveRecursive(xMutexAccessInputs);
|
|
}
|
|
else
|
|
{
|
|
sChamperTemperature.state = MEASUREMENT_FAULT;
|
|
sOutdoorTemperature.state = MEASUREMENT_FAULT;
|
|
sInletFlowTemperature.state = MEASUREMENT_FAULT;
|
|
sReturnFlowTemperature.state = MEASUREMENT_FAULT;
|
|
|
|
ESP_LOGE(TAG, "Unable to take mutex: taskInput()");
|
|
}
|
|
}
|
|
}
|
|
|
|
sMeasurement getChamberTemperature(void)
|
|
{
|
|
sMeasurement ret;
|
|
ret.state = MEASUREMENT_FAULT;
|
|
if (xSemaphoreTakeRecursive(xMutexAccessInputs, pdMS_TO_TICKS(5000)) == pdTRUE)
|
|
{
|
|
ret = sChamperTemperature;
|
|
xSemaphoreGiveRecursive(xMutexAccessInputs);
|
|
}
|
|
else
|
|
{
|
|
ESP_LOGE(TAG, "Unable to take mutex: getChamberTemperature()");
|
|
}
|
|
return ret;
|
|
}
|
|
|
|
sMeasurement getOutdoorTemperature(void)
|
|
{
|
|
sMeasurement ret;
|
|
ret.state = MEASUREMENT_FAULT;
|
|
if (xSemaphoreTakeRecursive(xMutexAccessInputs, pdMS_TO_TICKS(5000)) == pdTRUE)
|
|
{
|
|
ret = sOutdoorTemperature;
|
|
xSemaphoreGiveRecursive(xMutexAccessInputs);
|
|
}
|
|
else
|
|
{
|
|
ESP_LOGE(TAG, "Unable to take mutex: getOutdoorTemperature()");
|
|
}
|
|
return ret;
|
|
}
|
|
|
|
sMeasurement getInletFlowTemperature(void)
|
|
{
|
|
sMeasurement ret;
|
|
ret.state = MEASUREMENT_FAULT;
|
|
if (xSemaphoreTakeRecursive(xMutexAccessInputs, pdMS_TO_TICKS(5000)) == pdTRUE)
|
|
{
|
|
ret = sInletFlowTemperature;
|
|
xSemaphoreGiveRecursive(xMutexAccessInputs);
|
|
}
|
|
else
|
|
{
|
|
ESP_LOGE(TAG, "Unable to take mutex: getInletFlowTemperature()");
|
|
}
|
|
return ret;
|
|
}
|
|
|
|
sMeasurement getReturnFlowTemperature(void)
|
|
{
|
|
sMeasurement ret;
|
|
ret.state = MEASUREMENT_FAULT;
|
|
if (xSemaphoreTakeRecursive(xMutexAccessInputs, pdMS_TO_TICKS(5000)) == pdTRUE)
|
|
{
|
|
ret = sReturnFlowTemperature;
|
|
xSemaphoreGiveRecursive(xMutexAccessInputs);
|
|
}
|
|
else
|
|
{
|
|
ESP_LOGE(TAG, "Unable to take mutex: getReturnFlowTemperature()");
|
|
}
|
|
return ret;
|
|
}
|
|
|
|
eBurnerErrorState getBurnerError(void)
|
|
{
|
|
eBurnerErrorState ret = FAULT;
|
|
if (xSemaphoreTakeRecursive(xMutexAccessInputs, pdMS_TO_TICKS(5000)) == pdTRUE)
|
|
{
|
|
ret = sBurnerErrorState;
|
|
xSemaphoreGiveRecursive(xMutexAccessInputs);
|
|
}
|
|
else
|
|
{
|
|
ESP_LOGE(TAG, "Unable to take mutex: getBurnerError()");
|
|
}
|
|
return ret;
|
|
} |