208 lines
7.8 KiB
C
208 lines
7.8 KiB
C
#ifndef _lmic_config_h_
|
|
#define _lmic_config_h_
|
|
|
|
// In the original LMIC code, these config values were defined on the
|
|
// gcc commandline. Since Arduino does not allow easily modifying the
|
|
// compiler commandline unless you modify the BSP, you have two choices:
|
|
//
|
|
// - edit {libraries}/arduino-lmic/project_config/lmic_project_config.h;
|
|
// - use a BSP like the MCCI Arduino BSPs, which get the configuration
|
|
// from the boards.txt file through a menu option.
|
|
//
|
|
// You definitely should not edit this file.
|
|
|
|
// set up preconditions, and load configuration if needed.
|
|
#ifndef _LMIC_CONFIG_PRECONDITIONS_H_
|
|
# include "lmic_config_preconditions.h"
|
|
#endif
|
|
|
|
// check post-conditions.
|
|
|
|
// make sure that we have exactly one target region defined.
|
|
#if CFG_LMIC_REGION_MASK == 0
|
|
# define CFG_eu868 1
|
|
#elif (CFG_LMIC_REGION_MASK & (-CFG_LMIC_REGION_MASK)) != CFG_LMIC_REGION_MASK
|
|
# error You can define at most one of CFG_... variables
|
|
#elif (CFG_LMIC_REGION_MASK & LMIC_REGIONS_SUPPORTED) == 0
|
|
# error The selected CFG_... region is not supported yet.
|
|
#endif
|
|
|
|
// make sure that LMIC_COUNTRY_CODE is defined.
|
|
#ifndef LMIC_COUNTRY_CODE
|
|
# define LMIC_COUNTRY_CODE LMIC_COUNTRY_CODE_NONE
|
|
#endif
|
|
|
|
// if the country code is Japan, then the region must be AS923
|
|
#if LMIC_COUNTRY_CODE == LMIC_COUNTRY_CODE_JP && CFG_region != LMIC_REGION_as923
|
|
# error "If country code is JP, then region must be AS923"
|
|
#endif
|
|
|
|
// check for internal consistency
|
|
#if !(CFG_LMIC_EU_like || CFG_LMIC_US_like)
|
|
# error "Internal error: Neither EU-like nor US-like!"
|
|
#endif
|
|
|
|
// This is the SX1272/SX1273 radio, which is also used on the HopeRF
|
|
// RFM92 boards.
|
|
//#define CFG_sx1272_radio 1
|
|
// This is the SX1276/SX1277/SX1278/SX1279 radio, which is also used on
|
|
// the HopeRF RFM95 boards.
|
|
//#define CFG_sx1276_radio 1
|
|
|
|
// ensure that a radio is defined.
|
|
#if ! (defined(CFG_sx1272_radio) || defined(CFG_sx1276_radio))
|
|
# warning Target radio not defined, assuming CFG_sx1276_radio
|
|
#define CFG_sx1276_radio 1
|
|
#elif defined(CFG_sx1272_radio) && defined(CFG_sx1276_radio)
|
|
# error You can define at most one of CFG_sx1272_radio and CF_sx1276_radio
|
|
#endif
|
|
|
|
// LMIC requires ticks to be 15.5μs - 100 μs long
|
|
#ifndef OSTICKS_PER_SEC
|
|
// 16 μs per tick
|
|
# ifndef US_PER_OSTICK_EXPONENT
|
|
# define US_PER_OSTICK_EXPONENT 4
|
|
# endif
|
|
# define US_PER_OSTICK (1 << US_PER_OSTICK_EXPONENT)
|
|
# define OSTICKS_PER_SEC (1000000 / US_PER_OSTICK)
|
|
#endif /* OSTICKS_PER_SEC */
|
|
|
|
#if ! (10000 <= OSTICKS_PER_SEC && OSTICKS_PER_SEC < 64516)
|
|
# error LMIC requires ticks to be 15.5 us to 100 us long
|
|
#endif
|
|
|
|
// Change the SPI clock speed if you encounter errors
|
|
// communicating with the radio.
|
|
// The standard range is 125kHz-8MHz, but some boards can go faster.
|
|
#ifndef LMIC_SPI_FREQ
|
|
#define LMIC_SPI_FREQ 1E6
|
|
#endif
|
|
|
|
// Set this to 1 to enable some basic debug output (using printf) about
|
|
// RF settings used during transmission and reception. Set to 2 to
|
|
// enable more verbose output. Make sure that printf is actually
|
|
// configured (e.g. on AVR it is not by default), otherwise using it can
|
|
// cause crashing.
|
|
#ifndef LMIC_DEBUG_LEVEL
|
|
#define LMIC_DEBUG_LEVEL 0
|
|
#endif
|
|
|
|
// Enable this to allow using printf() to print to the given serial port
|
|
// (or any other Print object). This can be easy for debugging. The
|
|
// current implementation only works on AVR, though.
|
|
//#define LMIC_PRINTF_TO Serial
|
|
|
|
// Enable this to use interrupt handler routines listening for RISING signals.
|
|
// Otherwise, the library polls digital input lines for changes.
|
|
//#define LMIC_USE_INTERRUPTS
|
|
|
|
// If DISABLE_LMIC_FAILURE_TO is defined, runtime assertion failures
|
|
// silently halt execution. Otherwise, LMIC_FAILURE_TO should be defined
|
|
// as the name of an object derived from Print, which will be used for
|
|
// displaying runtime assertion failures. If you say nothing in your
|
|
// lmic_project_config.h, runtime assertion failures are displayed
|
|
// using the Serial object.
|
|
#if ! defined(DISABLE_LMIC_FAILURE_TO) && ! defined(LMIC_FAILURE_TO)
|
|
#define LMIC_FAILURE_TO Serial
|
|
#endif
|
|
|
|
// define this in lmic_project_config.h to disable all code related to joining
|
|
//#define DISABLE_JOIN
|
|
// define this in lmic_project_config.h to disable all code related to ping
|
|
//#define DISABLE_PING
|
|
// define this in lmic_project_config.h to disable all code related to beacon tracking.
|
|
// Requires ping to be disabled too
|
|
//#define DISABLE_BEACONS
|
|
|
|
// define these in lmic_project_config.h to disable the corresponding MAC commands.
|
|
// Class A
|
|
//#define DISABLE_MCMD_DutyCycleReq // duty cycle cap
|
|
//#define DISABLE_MCMD_RXParamSetupReq // 2nd DN window param
|
|
//#define DISABLE_MCMD_NewChannelReq // set new channel
|
|
//#define DISABLE_MCMD_DlChannelReq // set downlink channel for RX1 for given uplink channel.
|
|
//#define DISABLE_MCMD_RXTimingSetupReq // delay between TX and RX
|
|
// Class B
|
|
//#define DISABLE_MCMD_PingSlotChannelReq // set ping freq, automatically disabled by DISABLE_PING
|
|
//#define ENABLE_MCMD_BeaconTimingAns // next beacon start, DEPRECATED, normally disabled by DISABLE_BEACON
|
|
|
|
// DEPRECATED(tmm@mcci.com); replaced by LMIC.noRXIQinversion (dynamic). Don't define this.
|
|
//#define DISABLE_INVERT_IQ_ON_RX
|
|
|
|
// This allows choosing between multiple included AES implementations.
|
|
// Make sure exactly one of these is uncommented.
|
|
//
|
|
// This selects the original AES implementation included LMIC. This
|
|
// implementation is optimized for speed on 32-bit processors using
|
|
// fairly big lookup tables, but it takes up big amounts of flash on the
|
|
// AVR architecture.
|
|
// #define USE_ORIGINAL_AES
|
|
//
|
|
// This selects the AES implementation written by Ideetroon for their
|
|
// own LoRaWAN library. It also uses lookup tables, but smaller
|
|
// byte-oriented ones, making it use a lot less flash space (but it is
|
|
// also about twice as slow as the original).
|
|
// #define USE_IDEETRON_AES
|
|
|
|
#if ! (defined(USE_ORIGINAL_AES) || defined(USE_IDEETRON_AES))
|
|
# define USE_IDEETRON_AES
|
|
#endif
|
|
|
|
#if defined(USE_ORIGINAL_AES) && defined(USE_IDEETRON_AES)
|
|
# error "You may define at most one of USE_ORIGINAL_AES and USE_IDEETRON_AES"
|
|
#endif
|
|
|
|
// LMIC_DISABLE_DR_LEGACY
|
|
// turn off legacy DR_* symbols that vary by bandplan.
|
|
// Older code uses these for configuration. EU868_DR_*, US915_DR_*
|
|
// etc symbols are prefered, but breaking older code is inconvenient for
|
|
// everybody. We don't want to use DR_* in the LMIC itself, so we provide
|
|
// this #define to allow them to be removed.
|
|
#if !defined(LMIC_DR_LEGACY)
|
|
# if !defined(LMIC_DISABLE_DR_LEGACY)
|
|
# define LMIC_DR_LEGACY 1
|
|
# else // defined(LMIC_DISABLE_DR_LEGACY)
|
|
# define LMIC_DR_LEGACY 0
|
|
# endif // defined(LMIC_DISABLE_DR_LEGACY)
|
|
#endif // LMIC_DR_LEGACY
|
|
|
|
// LMIC_ENABLE_DeviceTimeReq
|
|
// enable support for MCMD_DeviceTimeReq and MCMD_DeviceTimeAns
|
|
// this is always defined, and non-zero to enable it.
|
|
#if !defined(LMIC_ENABLE_DeviceTimeReq)
|
|
# define LMIC_ENABLE_DeviceTimeReq 0
|
|
#endif
|
|
|
|
// LMIC_ENABLE_user_events
|
|
// Enable/disable support for programmable callbacks for events, rx, and tx.
|
|
// This is always defined, and non-zero to enable. Default is enabled.
|
|
#if !defined(LMIC_ENABLE_user_events)
|
|
# define LMIC_ENABLE_user_events 1
|
|
#endif
|
|
|
|
// LMIC_ENABLE_onEvent
|
|
// Enable/disable support for out-call to user-supplied `onEvent()` function.
|
|
// This is always defined, and non-zero to enable. Default is enabled.
|
|
#if !defined(LMIC_ENABLE_onEvent)
|
|
# define LMIC_ENABLE_onEvent 1
|
|
#endif
|
|
|
|
// LMIC_ENABLE_long_messages
|
|
// LMIC certification requires that this be enabled.
|
|
#if !defined(LMIC_ENABLE_long_messages)
|
|
# define LMIC_ENABLE_long_messages 1 /* PARAM */
|
|
#endif
|
|
|
|
// LMIC_ENABLE_event_logging
|
|
// LMIC debugging for certification tests requires this, because debug prints affect
|
|
// timing too dramatically. But normal operation doesn't need this.
|
|
#if !defined(LMIC_ENABLE_event_logging)
|
|
# define LMIC_ENABLE_event_logging 0 /* PARAM */
|
|
#endif
|
|
|
|
// LMIC_LORAWAN_SPEC_VERSION
|
|
#if !defined(LMIC_LORAWAN_SPEC_VERSION)
|
|
# define LMIC_LORAWAN_SPEC_VERSION LMIC_LORAWAN_SPEC_VERSION_1_0_3
|
|
#endif
|
|
|
|
#endif // _lmic_config_h_
|